The IC670ALG310 output module is compact in size and it can fit into small spaces. For input data, it takes 0 to 8 words of analog output data, 0 to 3 bytes of input data for the module and channel status, and 0 to 2 bytes of output data for clearing alarms. All of the data exchanges takes place between the output module and the bus interface unit. The IC670ALG310 output module comes with a “Channel Active” feature that lets the operators configure an individual channel as either active or inactive. The module also comes with local output default features that help to configure the data to the default settings or to zero for the module data in the bus interface unit. The module draws 170 milliamps of current from the bus interface. The resolution of the module is 14 bits and the magnitude data size is 14 bits.

Brand GE Fanuc

Series Rx7i PACsystem

Part Number IC670ALG310

Description Analog output module

Voltage -10 to 10 Volts

Over/Under Range 50 mV

Current Drawn From Bus 170 mA

Resolution 14 bits

Magnitude 14 bits

Input Data 0-8 words, 0-3 bytes, 0-2 bytes

The IC670GBI001 isa communication module from the Field Control series of GE Fanuc. This module specifically supports Genius Bus protocol, allowing users to implement distributed I/O architecture. This module is coupled with a Genius Bus Interface Unit terminal block to enable mounting DIN rail or Panel mounting. This terminal block module also hosts the screw terminals where main genius bus connection and optional redundancy network connectivity can be established.

The IC670GBI001 supports daisy-chain topology architecture on both the primary and secondary bus. The supported data transmission speed of this module are 153.6 Kbaud standard, 153.6 Kbaud extended, 76.8 Kbaud, or 38.4 Kbaud with available memory allocations for a variety of data types such as 256 Bytes for discrete inputs (%I), status data and intelligent modules; 256 Bytes for discrete outputs (%Q) and fault clearing for intelligent modules; 256 bytes for analog inputs (%AI) and 256 bytes for analog outputs (%AQ). Both the primary and secondary bus connection points are provided with terminating resistor connection points that is used to terminate the bus connection and maintain a stable connection across the network. This termination point is specifically allocated across the serial 1 and serial 2 terminals, installed at the start (first node) and end of the bus (last node). Resistor values include 75 ohm, 100 ohm, 120 ohm or 150 ohm terminating resistor. Pre-molded bus cables may also be used with this Bus Interface module with catalog number IC660BLM508 which uses 75 ohm resistor and IC660BLM506 which uses 150 ohm resistor.

The IC670GBI102 bus interface unit is a Field Control bus interface unit manufactured by GE Fanuc. The unit is part of the GE Field Control series and it is compatible with the IC670GB and IC670GBI modules. This programmable control module operates within a temperature range of 0 to 55 degrees Celsius (32 to 131 degrees Fahrenheit) and it has a storage temperature range of -40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit). The relative humidity range of the IC670GBI102 bus interface module is 5 to 95% (non-condensing). The IC670GBI102 bus interface unit can withstand a solid vibration and shock levels that are typical for industrial environments and it is installed on panel-mounted DIN rail.

The IC670GBI102 bus interface unit can operate on both AC and DC power sources and the operating voltage range is 90 to 135 Volts AC and 105 to 150 Volts DC. The nominal rated voltage of the IC670GBI102 bus interface unit is 115 Volts AC and 125 Volts DC. The power consumption is a maximum of 48 Volt-Amps at 115 Volts AC and a maximum of 24 Watts at 125 Volts AC. The power consumption is specified for operation on a full load. The inrush current of the unit is 20 Amps at peak for a maximum of 3 milliseconds. The maximum holdup time of the unit is 20 milliseconds while the power supply output voltage is 6.5 Volts DC. The input frequency of the unit is 47 to 63 Hertz. The terminal block of the bus interface unit is 16 milliamps and its reliability rating is more than 600,000 hours.

Technical Specifications for IC670GBI102

Brand GE Fanuc

Series Field Control

Manufacturer: GE Fanuc

Manufacturer GE Fanuc

Product Type: Profibus Bus Interface

Part Number IC670GBI102

Series Field I/O control

Product Family Field Control

Type Bus interface unit

Part Number IC670GBI102

Compatibility Field control IC670GB / IC670GBI

Part Number: IC670GBI102

Product Description Bus Interface Unit (BUI)

Nominal Rated Voltage 115 Volts AC, 125 Volts DC

Transmission speed 53.6 Kbaud standard, 153.6 Kbaud extended, 76.8 Kbaud, or 38.4 Kbaud

Supply Voltage range 90 to 135 VAC, 105 to 150 VDC

Nominal supply voltage 115 VAC, 125 VDC

Terminating resistors 75 ohm, 100 ohm, 120 ohm, 150 ohm resistor

Voltage Range 90 to 135 Volts AC / 105 to 150 Volts DC

Power consumption 115 VAC: 48VA maximum at full load (nominal voltage) 25 VAC: 24W maximum at full load (nominal voltage)

Pre-fabricated cables IC660BLM506, IC660BLM508

Frequency 47 to 63 Hertz

Hot insertion and removal of modules IC670GBI002(F); IC670GBI102A

Inrush Current 15-50 Amps peak, 3 mS maximum

Power at 115 Volts AC 48 Volt-Amps (maximum) at full load

Reliability More than 183,000 hours operation MTBF, calculated

Power Supply Output 6.5 VDC ±5%

Power at 125 Volts AC 24 Watts (maximum) at full load

Mounting DIN Rail / Panel mount via the Profibus Bus Interface Unit (BIU) terminal block

Current output to modules 2:00 AM

Inrush Current 20 Amps (peak), 3 milliseconds (maximum)

Holdup time 10 ms

Power Supply Output 6.5 Volts DC

No. of supported I/O modules up to Eight (8) modules

Supported protocols Genius

Holdup Time 20 milliseconds (maximum)

Compatible Hand-Held Programmers IC660HHM501; IC693PRG300

Reliability More than 183,000 hours operation MTBF

Supported functions I/O forcing; Diagnostic display; Program upload/download

Product Lifecycle Status Discontinued/Obsolete

Power supply: 24 VDC

CPU Redundancy Supported

Hot Insertion and Removal of Modules Supported

Each output contacts are rated 5VDC / 24 VDC / 125 DC or and 120 / 240 VAC nominal voltages with actual voltage ranges of 0-130 VDC, 0-265 VAC, 47-63 Hz and the maximum load current per module is 16 A. The module has a fixed coil, moving armature relay type and has current consumption of 313 mA, maximum.

The module comes with typical rating of isolation between input to logic, user input to frame ground and group to group isolation specifically, 250 VAC continuous, 1500 VAC for 1 minute.

The module maximum current for resistive loads rated 2.0 Amps from 5 to 265VAC; 2.0 Amps from 5 to 30VDC and 0.2 Amps from 31 to 125VDC while the maximum inrush current is 5 A for 20 ms and maximum load current of 10 mA per input. The module’s response time for ON and Off signal transition are typical which is maximum of 10 ms while the maximum switching frequency of each channel is 20 cycles per minute if used with an inductive load.

The contact outputs of the module are made of Silver Alloy with contact resistance of 0.2 ohms at 1 A at 6 VDC. Each contact has operational life of 20 x 10^6 operations (mechanical) and 10^5 operations at rated resistive load (electrical).

The Field Control IC670MDL930 Relay Output Module is an isolated NO/NC relay discrete output module that is made by GE Fanuc. The IC670MDL930 Relay Output Module provides 8 isolated outputs that have 6 normally-open contacts and 2 normally-closed and normally-open contacts. These relays are also referred to as Form A relays and Form C relays, respectively. In order to reduce the high-frequency noise transient, the outputs are suppressed with an RC snubber. The Form A relay has normally-open contacts and the Form C relay has normally open or normally closed contacts. The contacts of the module are made of silver alloy. The mechanical life of the contacts is 20 x 10^6 operations and the electrical life of the contacts is 10^5 operations.

The IC670MDL930 Relay Isolated NO/NC Output Module requires more power from the BIU when it has a large number of connected relay output modules. The users must supply an external AC or DC power source to the load which is driven by the contacts. Each output has an indicator LED on the logic side. This module offers fault reporting facilities for efficient operation. It has 8 bits of discrete output data which is processed for use with the bus interface module. The IC670MDL930 Relay Output Module must be supplied with the power needed to energize the relay coils. The maximum load current of the module is 2 Amps at 5 to 265 Volts AC, 2 Amps at 5 to 30 Volts DC, and 0.2 Amps at 31 to 125 Volts DC. It comes with a fixed coil relay type with a moving armature. It draws 313 milliamps of maximum current from the bus interface module power supply in order to power up.

Brand GE Fanuc

Series Field Control

Manufacturer:GE Fanuc

Part Number IC670MDL930

Series Field I/O control

Part Number IC670MDL930

Product Description Relay output module

No of Channels Eight (8) relay outputs

Rated Voltage 5/24/125 Volts DC, 120/240 Volts AC

Contact Forms Six (6) Normally Open (N.O.) contacts (Form A); Two (2) Normally Closed (N.C.) contact (Form C

Voltage Range 0-130 Volts DC, 0-265 Volts AC

Frequency Range 47-63 Hertz

Rated Voltage 5/24/125 VDC, 120/240 VAC

Maximum Load Current 16 Amps per module

Voltage Range 0�30 VDC, 0�65 VAC (47�3 Hz)

Relay Type Fixed coil, moving armature

Maximum Load Current (resistive) 16 A per module

Current drawn from BIU 313 mA

LED indicators Individual channel LED; PWR LED

Switching Frequency 20 cycle/minute

Relay Type: Fixed coil, moving armature

Contact Type Silver Alloy

Current draw 313 mA

Protection Snubbber, no fuse

Maximum load current 2.0 Amps from 5 to 265VAC; 2.0 Amps from 5 to 30VDC; 0.2 Amps from 31 to 125VDC

Maximum Inrush 5 Amps for 20mS

Minimum Load Current 10 mA per point

Contact Life Mechanical: 20 x 10^6 operations; Electrical: 10^5 operations at rated resistive load

Protection Snubber (R=47.5 ohms, C=0.022 ufd). No fuse

Product Lifecycle Status Discontinued/Obsolete

The high-speed counter allows direct processing of rapid pulse signals of up to 1 MHz for industrial applications such as material handling, meter proving and velocity measurement. With the direct processing capability, the high-speed counter can detect inputs, count and respond with outputs without the need of communicating with a CPU. It’s configurable to count either up or down, both up and down or to count the difference existing between two variables. The module can be configured to provide either 1 complex counter, 2 identical and complex counters, or 4 identical and independent simple counters. The module comes with 12 positive source inputs with an input voltage range of either 5 V DV or 10 to 30 V DC. Furthermore, you’ll find 4 positive source outputs, internal module diagnostics, and a removable terminal board used during field wiring. The IC694APU300 module provides two modes of operation when used in an RX3i system: Classic and Enhanced. By default, the module operates in classic mode. However, if you desire to use enhanced features, select ‘Enhanced mode�using the machine edition configuration tool.

Enhanced features include Support for up to 1 MHz input frequency from external devices and up to 2 MHz internal oscillator at clock input 1, support for both 32-bit counters and Z input events, configurable outputs, rollover detection flag and support for firmware updates over the backplane from the RX3i CPU. IC693APU300 also has a windowing feature that allows a user to define a range of counter accumulator values where the strobe is recognized as a valid input. Should the counter accumulator go outside this range, the strobe input is ignored. Since the module is considered an open type equipment, it should be installed into an enclosure with minimal pollution. For wiring connections, use copper wire with a minimum rating of 90 degrees Celsius. If two wires are allowed, then they should be of the same type. Before wiring, replacing modules, batteries, fuses or any other serviceable component, it’s recommended to TURN OFF the power. This is to avert any mishaps that may occur. Moreover, the product should be mounted in an enclosure certified for use in Zone 2, Group IIC, and rated IP54 minimum. During field wiring, shielded cable must be used for all cables connecting to the IC694APU300 High-speed Counter. The shielded cable should possess a high frequency ground within 6 inches of the IC694APU300 module.

Manufacturer GE Fanuc

Series Series 90-30

Part Number IC693APU300

Product Type High-Speed Counter Module

Minimum Count Speed 20 Kilohertz

Maximum Count Speed 80 Kilohertz

Wire Copper

Number of Inputs 12

Number of Outputs 4

Logic Type Positive

The IC693NIU004 is a Series 90-30 Programmable Logic Controller (PLC) module. This is specifically an Ethernet Network Interface Unit (NIU) that is primarily used for implementing distributed I/O architecture over Ethernet network utilizing Ethernet Global Data (EGD) protocol for exchanging I/O data, monitoring and control of remote systems over simplex or fault-tolerant Ethernet network topology. The IC693NIU004 comes with Two (2) Ethernet communication interface that features auto-sensing, auto-negotiation and supports a transmission rate of 10/100 Mbps. These ports utilize One (1) IP address, therefore functioning as a built-in Ethernet switch that can be used for Linear, Star, and Ring topologies. This module comes with the capability of processing and handling up to 2048 Discrete Inputs (%I); 2048 Discrete outputs (%Q); 1268 Analog input Words (%AI) and 512 Analog output Words (%AQ). Aside from these registers for physical I/Os, the IC693NIU004 also has built-in 4096 internal coil memory; 256 bits of temporary output coil, and 9999 register memory. This module supports interconnection of up to 8 baseplates being comprised of One (1) CPU baseplate and Seven (7) expansion and remote baseplates. The IC693NIU004 also supports the Secure Real-time Transport Protocol (SRTP) server. The IC693NIU004 comes with Status LED indicators such as EOK, LAN, STAT, and PS PORT. It is also provided with an Ethernet restart pushbutton which can be used to re-initialize the module without the need of removing power or using the programming software. An appropriate programming software package for use with this module is the CIMPLICITY Machine Edition Logic Developer 4.0, service pack 3, with Special 4 or later.

The GE Fanuc IC693NIU004 Ethernet Network Interface provides a gateway for the connection of the GE Fanuc Series 90-30 Programmable Logic Controllers to the industrial Ethernet protocol via a built-in 10/100 Base-T/TX Ethernet Switch. This Ethernet interface module comes equipped with two RJ45 ports with auto-sensing capabilities. Up to 2,048 discrete inputs and 2,048 discrete outputs can be connected to, monitored by, and controlled through the Ethernet protocol. The GE Fanuc IC693NIU004 Ethernet Network Interface can also handle up to 1268 analog inputs and up to 512 analog outputs. With such a high-speed and accurate processing and data transmission capabilities, this Ethernet Network interface module is ideal for industrial application processes spanning a high number of field devices.

The operating temperature for the GE Fanuc IC693NIU004 Ethernet Network Interface should remain between 0 and 60 degrees Celsius (32 and 140 degrees Fahrenheit) at all times. Performance issues may occur when the module is to be exposed to higher (or lower) temperatures than those in the rated temperature ranges for extended periods. The ambient humidity should also be controlled, so it is recommended to install the GE Fanuc IC693NIU004 Ethernet Network Interface inside a protected panelboard, preferably with climate control or forced air circulation. The installation of the unit should only be carried out by properly trained technicians, and only qualified technicians should perform any maintenance work, servicing, or repairs to the module. The configuration of the device is done through the CIMPLICITY Machine Edition Logic Developer software, which is required in order to perform basic activities such as assigning an IP address and setting up the subletting parameters.

  Technical Specifications for IC693NIU004

The IC693PWR331 is provided with an RS485 communication terminal. This port allows connection to workstation installed with GE Proficy Software for configuration. Additionally, the same port permits connection of Hand-Held Programmer (HHP) and other devices that are RS485 communication standard enabled.

The IC693PWR331 is provided with LED indicator that reports the state of the module as well as the components attached to the device. It has PWR, OK, RUN and BATT LED indicators. This power supply also hosts the battery back-up that maintain the contents of the PLC’s volatile memory. The BATT indicator is used to indicate the charge of the battery to provide reference as to when the battery must be replaced. The battery connection terminals as well as the incoming wires�termination strip are installed on the front panel, behind the swing door.

For the isolated supply, the bottom terminal of the IC693PWR331 power supply module is connected to the isolated +24 Volts DC output that is used to power the external circuits. The IC693PWR331 module runs with an input voltage ranging from 2 Volts DC to 30 Volts DC. The power supply device can be connected to a peripheral device or a computer’s serial port by using the RS 485 port located on the front panel. The IC693PWR331 module can be easily mounted in the leftmost slot of the Series 90-30 device baseplate. This unit should be kept away from dust, dirt, and all heat-generating devices.

FAQ for IC693PWR331

Brand GE Fanuc

Output Voltage 5 VDC: 300 Watts, maximum 24 VDC Relay: 15 watts maximum 24 VDC Isolated: 20 watts maximum

Inrush Current 4A peak, 100 ms maximum

Input Power 90 VA with VAC Input; 50 W with VDC Input

Input Voltage Range, DC Start: 21 to 56 VDC Run: 18 to 56 VDC

Nominal Rated Voltage 24VDC / 48VDC

No. of Outputs Three (3)

Protocol Support RS485

Product Type High-capacity power supply

Output Power 5 VDC and 24 VDC Relay: 15 watts maximum 24 VDC Relay: 15 watts maximum 24 VDC Isolated: 20 watts maximum

Series 90-30 PLC

Part Number IC693PWR331

Load capacity 30 Watts

Holdup time 14 milliseconds, minimum

LED indicators: PWR, OK, RUN, BATT

Description Power Supply device

Voltage 24 Volts DC

Standard UL, CE

Full load power rating 50 Watts

Number of terminal screws 3

Product Lifecycle Status* Discontinued/Obsolete

There are 16 channels total on the IC694ALG233 input module and each channel can be configured with the following input ranges: 0 to 20 milliamps, 4 to 20 milliamps enhanced, and 4 to 20 milliamps normal. High and low alarm limits can also be configured through software. For the 4 to 20 milliamps enhanced current range, a low alarm limit can be configured for the detection of an input current between 4 and 20 milliamps. This feature can be used to provide open-wire detection in 4 to 20 milliamps enhanced current rated applications. The IC694ALG233 input module also reports the module status and external power supply status to the system CPU by using the assigned program reference addresses. The IC694ALG233 input module can be installed in I/O slots that come with a serial connector. The IC694ALG233 input module supports hot removal and insertion. The firmware on the IC694ALG233 input module can be upgraded to enable new features.

  Technical Specifications for IC694ALG233

Brand GE Fanuc

Series RX3i PacSystem

Part Number IC694ALG233

Product Type Analog current input module

Input Channels 16

Power Requirement 120 milliamps at 5 Volts DC

External Supply Voltage Range 20 to 30 Volts DC

Input Low-Pass Filter Response 23 Hertz

Operating Temperature 0 to 60 degrees Celsius

Relative Humidity 5 to 95%

Storage Temperature -40 to 100 degrees Celsius

IC694MDL655 32-Point (4 isolated groups of 8), 24 VDC, Positive/Negative Logic, Input module RX3i Series. Input Current: 7 mA. Input Voltage Range: 0 to +30VDC. Power Consumption: 195 mA from 5V bus, 224 mA from 24V supply.

Product Description

The IC694MDL655 is a 32-Point, 24 VDC, Positive/Negative Logic, Input module from the GE Fanuc RX3i Series. This module provides 32 discrete input points.  The inputs are positive or negative logic inputs and will operate at levels up to 30V.  See specifications for this unit on IC694MDL655’s website page.

Technical Specifications

Rated Voltage: 24 volts DC

# of Inputs: 32 (4 isolated groups of 8) 

Freq: N/A

Input Current: 7 mA

Input Voltage Range:  0 to +30VDC

Power Consumption:  195 mA from 5V bus, 224 mA from 24V supply

Technical Information

Specifications

RX3i CPUs like this one are designed for real-time control of machines, processes, and material handling systems. They can be programmed in C, or in three of the five programming languages recognized by the IEC (International Electrotechnical Commission). From the IEC language list specifically, you can program IC695CPU315 in Ladder Logic (Ladder Diagram), Structured Text, or Function Block Diagram languages. Only the Sequential Function Chart and Instruction List language options do not apply.

IC695CPU315 uses floating point algorithms, and its firmware can be upgraded within the system. Auto-located Symbolic Variables can use as much memory as they need, up to the full 20 MB capacity of user memory. The CPU comes factory-configured with two front=facing ports, an RS-485 serial port and an RS-232 serial port. Accordingly, you have both a 9-pin connector and a 15-pin connector. The CPU supports the SNP, Serial I/O, and Modbus Slave and Master serial protocols. IC695CPU315 also supports most of the older GE Fanuc Series 90-30 modules and expansion racks.

Technical Specifications

Processing Speed: 1 GHz

CPU Memory: 20 Mbytes

Floating Point: Yes

Serial Ports: 2

Serial Protocols: SNP, Serial I/O, Modbus Slave and Master

Embedded Comms:  RS-232, RS-486

Manufacturer GE Fanuc

Series RX3i PACSystems

Part Number IC695CPU315

Product Type CPU

Program Storage 20 MB of RAM, 20 MB of flash memory

Power Requirements 3.3V DC and 1 Amp, 5V DC and 1.2 Amp

Embedded Communications Ports RS-232, RS-485

Serial Protocol Support Modbus RTU Slave, SNP, Serial I/O protocols

Program Blocks Up to 512 program blocks

Operating Temperature 0-60 degrees Celsius